Results 1 to 10 of 11

Thread: Plugging port hole in Sierra 2 center that's in a cabinet?

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    May 2016
    Posts
    169

    Default Plugging port hole in Sierra 2 center that's in a cabinet?

    I have LRC S2's and the center is in a Sanus media cabinet like below. I could hear the center sounding kind of boxy and felt like the sound was bouncing around inside the cabinet. So I put a small roll of acoustic foam in the back vent as a plug and it seems to sound better.

    Any better options? Maybe just putting a 12" x 24" piece of foam around the back of the speaker, but a few inches behind and not blocking the hole? I didn't have a piece to try.

    http://www.sanus.com/assets/products...b_LS_570px.jpg

  2. #2
    Join Date
    Apr 2015
    Posts
    46

    Default Re: Plugging port hole in Sierra 2 center that's in a cabinet?

    Is it crossed over to a sub? Is the speaker at all recessed into the cabinet? Can you remove the center face of the cabinet to see if maybe it is contributing?

    I have my Sierra 2 center is a similar shaped salamander cabinet, crossed at 80hz, door off with the speaker angled slightly up and extending slightly out of the cabinet. I don't hear anything boxy or any bouncing around in the cabinet. It sounds like the LRs.
    Attached Images Attached Images

  3. #3
    Join Date
    Dec 2013
    Posts
    360

    Default Re: Plugging port hole in Sierra 2 center that's in a cabinet?

    I took some measurements of my Sierra-2 running full range with and without the port plugged. This was with the speaker sitting on a speaker stand, microphone at my couch, and all room correction turned off.


  4. #4
    Join Date
    May 2016
    Posts
    169

    Default Re: Plugging port hole in Sierra 2 center that's in a cabinet?

    Cool graph. What software and setup do you use to capture that?

    What's the chart look like with room correction on?

    Thx!

  5. #5
    Join Date
    Apr 2015
    Posts
    46

    Default Re: Plugging port hole in Sierra 2 center that's in a cabinet?

    Maybe I spoke too soon about not being boxy. Center does have a decent peak at around 80 Hz. Maybe the correction is fixing any boxy sounds???

    Edit: Are these ARC graphs with Anthem provided mic anywhere close to what I'd get with REW and a real mic? ... This rabbit hole looks pretty deep.
    Attached Images Attached Images
    Last edited by Todd WI; 02-10-2017 at 06:33 PM.

  6. #6
    Join Date
    Aug 2003
    Location
    USA
    Posts
    5,538

    Default Re: Plugging port hole in Sierra 2 center that's in a cabinet?

    Quote Originally Posted by Todd WI View Post
    Maybe I spoke too soon about not being boxy. Center does have a decent peak at around 80 Hz. Maybe the correction is fixing any boxy sounds???

    Edit: Are these ARC graphs with Anthem provided mic anywhere close to what I'd get with REW and a real mic? ... This rabbit hole looks pretty deep.
    That 80Hz peak is only +4dB, typical in-room peaks are +/- 10dB or higher. This is actually a fantastic in-room response, esp when considering the placement. The peak is also more likely caused by floor bounce than the enclosure the speaker is placed in.

    Plugging the port reduces the peak because it reduces the bass response of the speaker. The better option is to use auto-eq.
    .
    .
    .
    Good Sound To You!

    David Fabrikant
    www.ascendacoustics.com

  7. #7
    Join Date
    Dec 2013
    Posts
    360

    Default Re: Plugging port hole in Sierra 2 center that's in a cabinet?

    Quote Originally Posted by Blingleberry View Post
    Cool graph. What software and setup do you use to capture that?

    What's the chart look like with room correction on?

    Thx!
    I'm using Room EQ Wizard with a Umik-1 microphone. I'll see if I can dig up the room corrected measurement.

  8. #8
    Join Date
    May 2016
    Posts
    169

    Default Re: Plugging port hole in Sierra 2 center that's in a cabinet?

    Yes, I think it's crossed at 80. I had it in a config like yours but then put the door back on and have it recessed a bit. The door has a thin metal grill. I just liked how it looked better. Maybe I'll try it again though.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •