Results 1 to 10 of 18

Thread: stands for 340s

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Nov 2005
    Posts
    61

    Default

    MrTomasulo, you thinking of building some? I built these:
    http://gallery.avsforum.com/showphot...ppuser/7456874
    for real cheap - pretty easy too.

  2. #2
    Join Date
    Nov 2005
    Location
    Bristow, VA
    Posts
    12

    Default

    Quote Originally Posted by SteveCallas
    I built these:
    http://gallery.avsforum.com/showphot...ppuser/7456874
    for real cheap - pretty easy too.
    Steve, these stands look great. Have you divulged the secret of how you built them yet?

    Also, how are the speakers mounted to the stands? Do you just leave the speakers sitting on the stands or are they attached in any way?

    I will hopefully be getting 170 mains in the next few weeks and would love to try some DYI stands for them. Not sure if I will be able to accomplish anything like yours, but can't wait to have fun trying.

    By the way, loved the funny story thread over in the other forum. Lots of good info, well written, great story.

  3. #3
    Join Date
    Jan 2004
    Location
    Charter Oak, Iowa
    Posts
    579

    Default

    [QUOTE=Drew.Ri]Steve, these stands look great. Have you divulged the secret of how you built them yet?[QUOTE=Drew.Ri]



    Ditto on that! Throw in construction plans on that sub too! (or where to find the plans)

    Randy
    Last edited by Lou-the-dog; 11-23-2005 at 05:18 AM.

  4. #4
    Join Date
    Nov 2005
    Posts
    61

    Default

    Stands were easy. 2 layers of 3/4" MDF glued toegther for the top, and 2 layers for the bottom. Shape the bottom pieces however you want - I went with half arc fronts, and rounded ALL of the edges on the bottom pieces. The inside piece is of course smaller than the outer piece.

    The tops are octagonal in shape, with minmal rounding, as they really won't be seen. The inside piece is again smaller than the outer piece.

    The shafts are 3" diameter PVC. I got some threaded rod, 3/8" I believe, and have it running inside the tube. The inside piece sof MDF, on both the bottom and top, have holes in the center just big enough for the rod to be threaded through. The outside layers have much larger holes, something like 2.25", to allow room for a metal washer, the nut, and a socket wrench to tighten them down.

    There are plans for similar DIY stands on the internet, which were my inspiration, but they only used one layer for the top, and one for the bottom, meaning you would have to have countersunk holes to attach the nuts. My stands are much beefier and sturder with the two layers, and are held together very tight. Mine are fillable with sand as well, just use a neoprene washer on the inside of the tube where the rod meets the MDF.

    If that doesn't explain it, I can go into more detail for you if you like. VERY EASY project, for very cheap. The hardest part was trying to get the reflective finish.

    As for the sub, I think a webpage with detailed plans is in order in the future, as I'm getting many requests.

  5. #5
    Join Date
    Nov 2005
    Location
    Bristow, VA
    Posts
    12

    Default

    ok, that stand seems doable. Cheap anyway so I can mess it up plenty of times first. Are you able to run the wires through the stand?

  6. #6
    Join Date
    Nov 2005
    Posts
    61

    Default

    I'm not doing that with mine, but it would be easy enough to modify to make that possible.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •